EVT290A-CS20

EVT290A-CS20

Original price was: $35.00.Current price is: $23.00.

EVT290A-CS20 | 20mm Coupler Spacer for 290mm Truss

Dimensions & Specs
Spacer Length: 0.79 in (20 mm)
Outer Diameter: 1.96 in (50 mm) (Matches standard truss tubing)
Function: Expands truss length for custom measurements and adjustments

Construction
Material Type: Aluminum Alloy EN AW-6061 T6
Type: Double-Ended Male Conical Coupler
Compatibility: Fits standard 290mm Truss Conical Connection points

Finish & Features
Surface: Aluminum Brush Finish
Included: 20mm Spacer Coupler Only
Note: Coupler Pins and Cotter Pins are NOT included
Weight: 0.52 lb (0.24 kg)

In stock

SKU: EVT290A-CS20 Categories: , , ,

EVT290S Truss Systems Knowledge Center

EVT290A-CS20 20 mm Male Truss Coupler Spacer.
Adds 20 mm at One Compatible 290 mm Conical Truss Connection.

The EVT290A-CS20 is a double-ended male conical aluminum spacer that adds a fixed 20 mm / 0.79 in at one compatible 290 mm truss connection. Before installation, confirm the connection requires 20 mm and the complete joint—including receiver spacing, coupler engagement, coupler-pin length, r-clip fit, and all retaining hardware—remains suitable with the spacer installed. It is not a truss section, independent support point, or direct load-attachment location.

Product Facts

Model / SKUEVT290A-CS20
Product TypeDouble-Ended Male Conical Coupler Spacer
Added Length20 mm / 0.79 in
Outer Diameter50 mm / 1.96 in
MaterialAluminum Alloy EN AW-6061 T6
Component Weight0.52 lb / 0.24 kg
20 mmLength Added
50 mmOuter Diameter
100 mmOverall Height
0.52 lbComponent Weight
Not IncludedPins and R-Clips

What It Is

A Fixed 20 mm Spacer for One Specific Connection Condition.

The EVT290A-CS20 is a single-piece, double-ended male conical spacer with an integrated 20 mm collar. It is manufactured from Aluminum Alloy EN AW-6061 T6 with a brushed aluminum finish. Its fixed 20 mm geometry must match the approved requirement at the selected compatible connection.

Fixed 20 mm Collar
Adds 20 mm / 0.79 in; it does not provide adjustable travel.
Male-to-Male Form
Provides double-ended male conical interfaces for compatible truss receivers.
Brushed Aluminum
Manufactured from Aluminum Alloy EN AW-6061 T6 with a brushed finish.
Connection Component
It is not a truss section, support point, or direct load-attachment location.

What It Changes

It Adds 20 mm to One Joint. The Entire Joint Must Still Work as a Joint.

The CS20 adds 20 mm / 0.79 in at the selected compatible connection. It does not independently establish a load rating, allowable span, pick-point location, or support arrangement for the modified truss structure.

Changes
Adds 20 mm / 0.79 in to the selected compatible connection length.
Does Not Change
Does not establish an allowable span or load rating for the modified structure.
Does Not Include
Does not include coupler-pins, r-clips, or other retaining hardware.
Does Not Permit
Does not permit direct load attachment or support from the spacer joint.

What the Spacer Supports

Close a Larger Measured Difference at a Single Connection.

Use the EVT290A-CS20 where a verified compatible truss connection requires a 20 mm adjustment. Confirm the receiver interface, selected coupler, required pins and r-clips, complete layout, support conditions, and applicable engineering requirements before modifying any truss connection.

Custom Measurement Adjustments
Address a verified 20 mm measurement difference without modifying a truss section.
Planned Grids and Frames
Fine-tune planned technical grids, frames, and structures with measured interfaces.
Retrofit and Rework
Adjust a compatible existing structure where a documented project requirement calls for 20 mm.
EVT290S and F34 Systems
Use with verified compatible 290 mm conical truss systems and matching retention hardware.

Selection Guidance

Select It Only for an Actual 20 mm Need. Do Not Treat It as Two 10 mm Decisions.

A 20 mm spacer modifies one connection as one component. Select it only where the approved system requires 20 mm / 0.79 in at that joint and the coupler, coupler-pins, r-clips, and truss receivers are confirmed to work together as a complete connection.

Measured 20 mm Difference
For a 20 mm addition at one specific verified connection.
Planned Structures
For grids, frames, and technical structures with measured interfaces.
Receiver and Coupler Check
For connections where complete receiver engagement remains possible.
No Unapproved Stacking
Do not stack spacers or substitute combinations without approval for the complete structure.

Included Components

One Spacer. Retaining Hardware Sold Separately.

The EVT290A-CS20 ships as one double-ended male conical spacer. It does not include coupler-pins, r-clips, or other retaining hardware. Select and verify all required hardware for the complete approved connection before installation.

1 Male-to-Male Spacer
One double-ended male conical spacer inserts between compatible truss receivers.
20 mm Length Added
Adds 20 mm / 0.79 in at the selected compatible connection point.
6061-T6 Aluminum
Manufactured from Aluminum Alloy EN AW-6061 T6 with a brushed finish.
No Retaining Hardware
Coupler-pins and r-clips are not included and must be selected for the verified connection.
Do not stack spacers without specific approval.

Use the selected spacer only for the approved measurement adjustment. Do not stack multiple spacers at one connection point without project-specific engineering approval for the completed connection.

Technical Reference

EVT290A-CS20 Specifications.

The following values identify the spacer dimensions, material, weight, included-component scope, and listed system fit. Confirm current manufacturer drawings, instructions, required retaining hardware, component condition, and project requirements before ordering, assembling, lifting, or loading a modified truss structure.

Identification

Product Information

Model / SKUEVT290A-CS20
BrandEvolve Truss
Product TypeDouble-Ended Male Conical Coupler Spacer
Component Weight0.52 lb / 0.24 kg

Dimensions

Size

Spacer Length20 mm / 0.79 in
Outer Diameter50 mm / 1.96 in
Overall Height100 mm

Construction

Material and Finish

MaterialEN AW-6061 T6 Aluminum
FinishBrushed Aluminum
Included HardwareNone, Pins and R-Clips Not Included

System Fit

Compatibility

Primary SystemsEVT290I, EVT290T, EVT290S
Listed CompatibilityF34 and EVT50ST, When Interfaces Match

System Compatibility

Use CS20 in Compatible 290 mm Conical Truss Connections.

The EVT290A-CS20 is a double-ended male conical spacer for compatible 290 mm conical truss connections. Compatibility requires matching receiver spacing, conical coupler dimensions, chord interfaces, coupler-pin length, r-clip fit, complete engagement, and engineering data for the modified structure.

EVT290S Compatibility
Use with compatible EVT290S sections, corners, bases, and accessories when the complete connection is verified.
F34 Compatibility
Use with F34-format components only when receivers, couplers, pins, and retention hardware match.
Connection Engagement
The 20 mm spacer changes joint depth. Confirm complete receiver engagement and suitable pin and retention hardware.
Mixed-System Verification
Confirm the complete connection with a physical ground test-fit before lifting the structure.
Mechanical fit does not establish structural suitability.

A spacer can physically fit within a connection without the completed modified structure having approved support or load conditions. Verify all interfaces, documentation, hardware, and project-specific engineering before use.

Installation Overview

Confirm the 20 mm Joint Before It Enters Service.

Install CS20 only in a verified compatible connection using serviceable components, correct pins and r-clips, current manufacturer instructions, and the approved project plan. Do not force a spacer or connection into alignment.

01 — Confirm Requirement
Confirm the approved truss system requires a 20 mm addition at the selected connection.
02 — Inspect Components
Inspect the spacer, receivers, couplers, pins, r-clips, and adjoining truss for damage or deformation.
03 — Test-Fit the Full Joint
Confirm all receivers, couplers, pins, and retainers achieve required engagement with the spacer installed.
04 — Secure and Inspect
Install required hardware fully, then inspect the complete joint before handling, lifting, or loading.

Safety and Engineering

A 20 mm Change Requires Complete Joint Confirmation.

The EVT290A-CS20 does not independently establish a load rating for the modified structure. The spacer changes connection geometry, so evaluate the completed layout for support conditions, joint engagement, installed loads, handling method, and engineering requirements. Do not support loads directly from the spacer connection unless the exact approved load case specifically permits it.

Do not exceed the capacity of the spacer, installed connection hardware, or completed truss system.
Do not support loads directly from the spacer connection unless the exact approved load case permits it.
Verify complete coupler engagement in both receivers after the spacer is installed.
Use pins and r-clips selected for the complete verified 20 mm connection.
Do not stack spacers at one connection point without project-specific engineering approval.
Use qualified rigging or engineering review for overhead, public-facing, outdoor, load-bearing, or regulated modified structures.

Variant Relationship

The Dimension Comes First. The Finish Comes Second.

Choose the single spacer whose fixed length matches the approved connection requirement. A black-finish version should be selected only when the same dimensional requirement also needs a black finish.

CS10
10 mm / 0.39 in, brushed aluminum.
CS10 Black
10 mm / 0.39 in, matte black.
CS20
20 mm / 0.79 in, brushed aluminum.
CS30
30 mm / 1.18 in, brushed aluminum.
Do not substitute two 10 mm spacers for one 20 mm spacer.

A 20 mm requirement calls for this single-piece spacer, not two stacked 10 mm units. Do not stack spacers or combine dimensions without engineering approval for the completed connection.

Product Questions

EVT290A-CS20 Questions.

What does the CS20 do?

It adds 20 mm / 0.79 in at one compatible 290 mm conical truss connection.

Why must engagement be checked?

The 20 mm collar changes connection depth, so the complete joint must retain suitable coupler, receiver, coupler-pin, and r-clip engagement.

Are coupler-pins included?

No. The spacer is supplied without coupler-pins or r-clips. Select them separately for the completed verified connection.

Can two CS10 spacers replace one CS20?

No. A 20 mm requirement calls for this single-piece spacer. Do not stack spacers or combine dimensions without engineering approval for the completed connection.

Need to Close a 20 mm Truss Measurement Difference?

Contact us for compatibility checks, retaining-hardware guidance, measurement review, quantities, CAD resources, and engineering coordination.

Contact UsRequest a Quote

Structural Solutions, Unmatched Innovation

Weight 0.52 lbs
Dimensions 2 × 2 × 2 in