Does the powder coat finish affect how this section connects to standard brushed aluminum truss components?

No. The end-plate geometry, bolt hole pattern, and connection hardware are identical between the black and standard aluminum versions. The powder coat is a surface finish only — it does not change the plate thickness, hole spacing, or structural interface. You can bolt the EVT12S-2FT Black directly to any compatible 12-inch plated truss section, whether it is black or brushed aluminum, using the same Grade 8 hardware.

How should I handle and transport powder-coated truss to avoid damaging the finish?

Use truss spacers or protective padding between sections when stacking for transport. Avoid dragging sections across concrete or metal surfaces. The powder coat resists normal wear from assembly and disassembly, but sharp impacts or prolonged friction against hard edges can chip the finish. If chipping occurs, touch-up paint matched to matte black can restore the appearance — the structural integrity is not affected by cosmetic surface damage.

What hardware is required for installation?

The section ships with 4x Grade 8 bolts, nuts, and washers for immediate assembly. Use only the included Grade 8 hardware or equivalent. Ensure all bolts are properly torqued to manufacturer specifications. Do not substitute lower-grade hardware, and verify all connections are secure before loading the structure.

EVT12S-2FT Black

EVT12S System Knowledge Center

2 Ft Black Square Box Truss End Plate Section.
Adds a 24 Inch Section to 12-Inch End-Plated Truss Systems.

The EVT12S-2FT-Black is a 24-inch matte black aluminum end-plate truss section for adding a two-foot length within EVT12S and 12-Inch End-Plated Truss Systems. It helps configure overall run dimensions when a standard section length is too long or too short. Allowable loading depends on the completed truss system, including its span, supports, connections, and applied loads.

Product Facts

Model / SKUEVT12S-2FT-Black

Product TypeBlack Square Aluminum End-Plate Truss Section

Overall Size12 x 12 x 24 in

Section Length24 in / 2 ft / 609.6 mm

MaterialEN AW-6061-T6 Aluminum

FinishMatte Black Powder Coat

2 ftSection Length

12 x 12 inTruss Profile

50 mmMain Tubing

20 lbSection Weight

4-BoltEnd-Plate Connection

Product Overview

A Two-Foot Black Section for 12-Inch End-Plated Truss Systems.

The EVT12S-2FT-Black provides a 24-inch intermediate section for adding length within EVT12S and 12-Inch End-Plated Truss Systems. The finish is matte black powder coat, and the section is built with 50 mm main chords and 25 mm diagonal brace tubing. Loading and connection requirements apply to the completed system.

Matte Black Finish

A matte black powder coat finish.

Diagonal Brace Tubing

0.98 in / 25 mm OD with a 0.12 in / 3 mm wall.

Main Chord Tubing

1.96 in / 50 mm OD with a 0.12 in / 3 mm wall.

End-Plate Connection

End-plated nut-and-bolt connection format.

Application Uses

For Systems That Call for A Two Foot Black Section.

This section may be considered where a matte black, two-foot length is specified within a completed truss system. Potential applications include lighting grids, scenic structures, exhibit displays, venue systems, touring equipment, and rental inventory. Supports, span, connections, and applied loads must be evaluated for the completed installation.

Lighting Grids

For end-plated grid systems that specify a black two-foot section.

Scenic Structures

For stage and scenic assemblies subject to complete-system review.

Trade Displays

For exhibit structures that call for a black 24-inch section.

Venue and Touring Systems

For installations and touring equipment that specify a two-foot length.

Rental Inventory

Adds a two-foot black-finish option to truss inventory.

Included Hardware

Supplied with Hardware for One Four-Point Connection.

Four Grade 8 bolts, four nuts, and four washers are included with the section. Confirm fastener requirements at every actual joint, including bolt length, condition, engagement, and the applicable manufacturer tightening procedure.

4 Grade 8 Bolts

Provided for the four-point end-plate connection.

4 Nuts

Included with the supplied bolts.

4 Washers

Included in the hardware set.

Connection Count

Account for hardware at each joint in the complete system.

Technical Reference

EVT12S-2FT-Black Truss Section Specifications.

Identification

Product Details

Model / SKUEVT12S-2FT-Black

BrandEvolve Truss

Product TypeBlack 2 Foot Square Aluminum End-Plate Truss Section

Warranty1-Year Limited Manufacturing-Defect Warranty

Dimensions

Overall Size

Width12 in / 304.8 mm

Height12 in / 304.8 mm

Depth / Length24 in / 2 ft / 609.6 mm

Weight20 lb / 9.07 kg

Material and Tubing

Construction

MaterialAluminum Alloy EN AW-6061-T6

Main Tubing1.96 in / 50 mm OD, 0.12 in / 3 mm Wall

Brace Tubing0.98 in / 25 mm OD, 0.12 in / 3 mm Wall

FinishMatte Black Powder Coat

Connection Context

System Interface

Connection TypeEnd-Plated Nut and Bolt

Included Hardware4 Grade 8 Bolts, Nuts, and Washers

CompatibilityEVT12S and 12-Inch End-Plated Truss Systems

CertificationTÜV Certified

Fit NoticeExact fit with other systems is not guaranteed

System Compatibility

EVT12S and 12-Inch End-Plated Truss Systems. Verify Every Connection.

The EVT12S-2FT-Black is designed for EVT12S and 12-Inch End-Plated Truss Systems. Exact fit with other systems is not guaranteed. Before combining components, verify end-plate dimensions and thickness, bolt-hole positions, chord alignment, hardware, fastener engagement, and completed-joint seating.

System Match

Confirm the system uses a standard 12-inch end-plated format.

End Plates

Compare plate dimensions and bolt-hole positions.

Hardware

Confirm appropriate fasteners and engagement.

Completed Joint

Inspect alignment and full seating before use.

Assembly Overview

Align the End Plates. Install and Check All Four Fasteners.

Assembly should be performed by personnel qualified for the truss system in accordance with applicable manufacturer requirements. This outline provides neither torque values nor installation approval.

01 — Inspect

Check tubing, diagonal bracing, welds, plates, holes, finish, and hardware for damage.

02 — Align

Bring compatible end plates together without forcing distorted parts.

03 — Install Hardware

Fit specified fasteners at all four locations with adequate engagement.

04 — Tighten

Follow the applicable manufacturer fastener procedure.

05 — Check Seating

Confirm required hardware and full plate seating.

06 — Inspect Before Service

Review the completed truss system and supports before loading.

Engineering Reference

Load-Span Reference for Completed EVT12S Truss Runs.

All truss loading calculations are based on a completed compatible 12 x 12 aluminum-truss run supported or suspended at both ends, under one stated static-load alternative. The values below do not rate an individual straight section, plate, or two-foot truss segment. A section changes the overall length and adds bolted joints; it does not increase the completed system’s allowable capacity.

Allowable loading reference for the documented 12 x 12 aluminum-truss analysis.
Load Case	Unit	10 ft 3.05 m	20 ft 6.11 m	30 ft 9.14 m	40 ft 12.23 m
Uniformly Distributed Load	lb/ft	472	115	60	31
Deflection	in	0.21	0.65	1.63	2.68
Center Point Load	lb	2,710	1,206	580	272
Deflection	in	0.20	0.56	1.31	2.04
Third Point Loads	lb each	1,744	888	600	442
Deflection	in	0.32	0.68	1.48	2.62
Quarter Point Loads	lb each	1,110	633	428	308
Deflection	in	0.33	0.68	1.54	2.54

Load cases: CPL — one center load · TPL — two equal third-point loads · QPL — two equal quarter-point loads · UDL — load distributed over the complete span

Load-Span Assumptions and Project Review

Table assumptions: The reference evaluates unbraced truss configured as a simply supported beam. The primary analyzed spans were 10 ft, 20 ft, 30 ft, and 40 ft. If CPL, TPL, or QPL loading occurs at a truss connection, a minimum of two chords is assumed to support the vertical load.

Not included: Shock loads, dynamic loads, and resultant horizontal rigging forces, including forces from bridles or baskets. UDL applies only when the load is evenly distributed across the entire span. Published load cases are alternatives and are not additive.

Licensed structural-engineer review is required for every truss system. These values are general planning reference only and do not approve or rate an individual straight section, a completed lighting plot, a ground-support structure, a goal post, a tower, a start/finish arch, a suspended configuration, an outdoor installation, a mixed-component build, or any other assembled truss system. Confirm the complete configuration, supports, connections, span, applied loads, attachment points, rigging, ballast or anchorage, environmental conditions, and applicable code requirements with a licensed structural engineer before use.

Current documentation: Product specifications, included hardware, compatibility information, and availability are subject to change. Verify current product drawings, manufacturer instructions, connection hardware, and applicable engineering information before ordering, assembling, or using this product.

Safety and Engineering

A Truss Section Adds Length. It Does Not Increase Truss Capacity.

Allowable loading depends on the complete truss system, including span, supports, orientation, joints, suspension method, and applied loads. Suspended, load-bearing, dynamic-load, and complex applications require qualified structural or entertainment-rigging review. No stand-alone capacity value or torque value is provided here.

Inspect the truss section, diagonal braces, welds, plates, bolt holes, hardware, and connected truss before every use.

Remove any component with cracks, bends, elongated holes, plate deformation, damaged welds, or substantial finish damage from service.

Install and tighten all required fasteners using the applicable manufacturer procedure.

Do not support loads directly from connection points without approval for the complete truss system.

Verify connection interfaces and completed-system suitability before combining different systems.

Have a competent person perform a documented inspection at least annually and remove unsafe parts from service.

Truss Section Questions

EVT12S-2FT-Black Frequently Asked Questions.

What is a black two-foot truss section used for?

It adds an exact 24 in / 2 ft section to a truss run where a black finish is specified. Typical jobs include lighting grids, scenic structures, exhibit displays, venue systems and touring rigs, where a run has to land on a pick point or a venue dimension.

Does the matte black powder coat change how the section fits or what it can carry?

No. The coating is a finish, so it does not change the end-plate interface or increase the capacity of the truss run. Verify end-plate dimensions, bolt-hole positions and hardware before connecting, and inspect the finish before each use. Substantial finish damage is grounds for removing the section from service.

Can I use the Load-Span Reference to rate this section?

No. The reference shows a completed 12 x 12 aluminum-truss run supported at both ends, not an individual section, and the values are planning reference only. Allowable loading depends on the span, supports, joints, suspension method and applied loads, so have a licensed structural engineer review any suspended, load-bearing or dynamic setup.

How heavy is the black two-foot section, and is it certified?

It weighs 20 lb / 9.07 kg and is built from EN AW-6061-T6 aluminum with 50 mm main tubing and 25 mm diagonal brace tubing. It is TÜV certified and carries a 1-Year Limited Manufacturing-Defect Warranty. Plan a safe lift when you place it overhead.

Need an EVT12S Two Foot Black Truss Section?

Contact us for truss section selection, listed compatibility information, product documentation, and quantity-quote support.

Structural Solutions, Unmatched Innovation

Weight	20 lbs
Dimensions	13 × 13 × 13 in