How many connection joints does a 5-foot section eliminate compared to building the same span from shorter lengths?

A single 5-foot section replaces what would otherwise require two or three shorter sections plus their connection hardware. For example, reaching 10 feet with two 5-foot sections means one bolted joint at the midpoint. Reaching the same 10 feet with five 2-foot sections means four joints. Each eliminated joint saves four bolts, four nuts, four washers, alignment time, and one more inspection point — so the time and hardware savings scale quickly across a full grid build.

Does the matte black finish affect how clamps and accessories grip the main chord tubing?

The powder coat adds a thin layer over the aluminum surface, which actually increases friction slightly compared to bare brushed aluminum. Truss clamps, half-couplers, and quick-release clamps all seat and grip normally on the coated surface. The finish does not affect the outer diameter enough to change clamp compatibility — standard 50 mm (2-inch) truss clamps fit the main chords the same as on the standard version.

EVT12S-5FT Black

EVT12S System Knowledge Center

5 Ft Black Square Box Truss End Plate Section.
A 60 Inch Straight Section for 12-Inch End-Plated Truss Systems.

The EVT12S-5FT-Black is a 60-inch matte black aluminum straight section for EVT12S and 12-Inch End-Plated Truss Systems. Its five-foot length can be specified as part of a completed truss run. Allowable loading depends on the complete system, including span, supports, connections, orientation, and applied loads.

Product Facts

Model / SKUEVT12S-5FT-Black

Product TypeBlack Square Aluminum End-Plate Truss Section

Overall Size12 x 12 x 60 in

Section Length60 in / 5 ft / 1524 mm

MaterialEN AW-6061-T6 Aluminum

FinishMatte Black Powder Coat

5 ftSection Length

12 x 12 inTruss Profile

50 mmMain Tubing

35 lbSection Weight

4-BoltEnd-Plate Connection

Product Overview

A 60-Inch Black Straight for 12-Inch End-Plated Truss Systems.

This five-foot component uses an end-plated nut-and-bolt connection. It is built with a matte black powder coat finish, 50 mm main tubing, and 25 mm diagonal brace tubing. Evaluate all loading and connection requirements at the completed-system level.

Matte Black Powder Coat

A matte black powder coat finish.

Diagonal Brace Tubing

0.98 in / 25 mm OD with a 0.12 in / 3 mm wall.

Main Chord Tubing

1.96 in / 50 mm OD with a 0.12 in / 3 mm wall.

End-Plate Connection

End-plated nut-and-bolt connection format.

Application Uses

For End-Plate Truss Systems Using A 60-Inch Black Straight.

This 60-inch matte black section may be specified within completed end-plate box truss systems for production, venue, studio, temporary, and seasonal applications. Confirm the complete system’s span, supports, connections, orientation, attachment points, environmental conditions, and applied loads before use.

Broadcast and Studio Systems

For completed truss systems used in broadcast and studio environments that specify matte black components.

Touring Production Systems

For touring truss inventory and production systems that call for a five-foot black straight section.

Nightclub and Venue Production

For venue production systems where a 60-inch black end-plate component is specified.

Product Launch Environments

For event-production truss systems used for product presentations and related installations.

Seasonal Event Builds

For temporary seasonal-event truss systems subject to completed-system review.

Included Hardware

Supplied with Hardware for One Four-Point Connection.

Four Grade 8 bolts, four nuts, and four washers are included with the section. Confirm fastener requirements at every actual joint, including bolt length, condition, engagement, and the applicable manufacturer tightening procedure.

4 Grade 8 Bolts

Provided for the four-point end-plate connection.

4 Nuts

Included with the supplied bolts.

4 Washers

Included in the hardware set.

Connection Count

Account for hardware at each joint in the complete system.

Technical Reference

EVT12S-5FT-Black Truss Section Specifications.

Identification

Product Details

Model / SKUEVT12S-5FT-Black

BrandEvolve Truss

Product TypeBlack 5 Foot Square Aluminum End-Plate Truss Section

Warranty1-Year Limited Manufacturing-Defect Warranty

Dimensions

Overall Size

Width12 in / 304.8 mm

Height12 in / 304.8 mm

Depth / Length60 in / 5 ft / 1524 mm

Weight35 lb / 15.88 kg

Material and Tubing

Construction

MaterialAluminum Alloy EN AW-6061-T6

Main Tubing1.96 in / 50 mm OD, 0.12 in / 3 mm Wall

Brace Tubing0.98 in / 25 mm OD, 0.12 in / 3 mm Wall

FinishMatte Black Powder Coat

Connection Context

System Interface

Connection TypeEnd-Plated Nut and Bolt

Included Hardware4 Grade 8 Bolts, Nuts, and Washers

CompatibilityEVT12S and 12-Inch End-Plated Truss Systems

CertificationTÜV Certified

Fit NoticeExact fit with other systems is not guaranteed

System Compatibility

EVT12S and 12-Inch End-Plated Truss Systems. Verify Every Connection.

The EVT12S-5FT-Black is designed for EVT12S and 12-Inch End-Plated Truss Systems. Exact fit with other systems is not guaranteed. Before combining components, verify end-plate dimensions and thickness, bolt-hole positions, chord alignment, hardware, fastener engagement, and completed-joint seating.

System Match

Confirm the system uses a standard 12-inch end-plated format.

End Plates

Compare plate dimensions and bolt-hole positions.

Hardware

Confirm appropriate fasteners and engagement.

Completed Joint

Inspect alignment and full seating before use.

Assembly Overview

Align the End Plates. Install and Check All Four Fasteners.

Assembly should be performed by personnel qualified for the truss system in accordance with applicable manufacturer requirements. This outline provides neither torque values nor installation approval.

01 — Inspect

Check tubing, diagonal bracing, welds, plates, holes, finish, and hardware for damage.

02 — Align

Bring compatible end plates together without forcing distorted parts.

03 — Install Hardware

Fit specified fasteners at all four locations with adequate engagement.

04 — Tighten

Follow the applicable manufacturer fastener procedure.

05 — Check Seating

Confirm required hardware and full plate seating.

06 — Inspect Before Service

Review the completed truss system and supports before loading.

Engineering Reference

Load-Span Reference for Completed EVT12S Truss Runs.

All truss loading calculations are based on a completed compatible 12 x 12 aluminum-truss run supported or suspended at both ends, under one stated static-load alternative. The values below do not rate an individual straight section, plate, or five-foot truss segment. A section changes the overall length and adds bolted joints; it does not increase the completed system’s allowable capacity.

Allowable loading reference for the documented 12 x 12 aluminum-truss analysis.
Load Case	Unit	10 ft 3.05 m	20 ft 6.11 m	30 ft 9.14 m	40 ft 12.23 m
Uniformly Distributed Load	lb/ft	472	115	60	31
Deflection	in	0.21	0.65	1.63	2.68
Center Point Load	lb	2,710	1,206	580	272
Deflection	in	0.20	0.56	1.31	2.04
Third Point Loads	lb each	1,744	888	600	442
Deflection	in	0.32	0.68	1.48	2.62
Quarter Point Loads	lb each	1,110	633	428	308
Deflection	in	0.33	0.68	1.54	2.54

Load cases: CPL — one center load · TPL — two equal third-point loads · QPL — two equal quarter-point loads · UDL — load distributed over the complete span

Load-Span Assumptions and Project Review

Table assumptions: The reference evaluates unbraced truss configured as a simply supported beam. The primary analyzed spans were 10 ft, 20 ft, 30 ft, and 40 ft. If CPL, TPL, or QPL loading occurs at a truss connection, a minimum of two chords is assumed to support the vertical load.

Not included: Shock loads, dynamic loads, and resultant horizontal rigging forces, including forces from bridles or baskets. UDL applies only when the load is evenly distributed across the entire span. Published load cases are alternatives and are not additive.

Licensed structural-engineer review is required for every truss system. These values are general planning reference only and do not approve or rate an individual straight section, a completed lighting plot, a ground-support structure, a goal post, a tower, a start/finish arch, a suspended configuration, an outdoor installation, a mixed-component build, or any other assembled truss system. Confirm the complete configuration, supports, connections, span, applied loads, attachment points, rigging, ballast or anchorage, environmental conditions, and applicable code requirements with a licensed structural engineer before use.

Current documentation: Product specifications, included hardware, compatibility information, and availability are subject to change. Verify current product drawings, manufacturer instructions, connection hardware, and applicable engineering information before ordering, assembling, or using this product.

Safety and Engineering

A Truss Section Adds Length. It Does Not Increase Truss Capacity.

Allowable loading depends on the complete truss system, including span, supports, orientation, joints, suspension method, and applied loads. Suspended, load-bearing, dynamic-load, and complex applications require qualified structural or entertainment-rigging review. No stand-alone capacity value or torque value is provided here.

Inspect the truss section, diagonal braces, welds, plates, bolt holes, hardware, and connected truss before every use.

Remove any component with cracks, bends, elongated holes, plate deformation, damaged welds, or substantial finish damage from service.

Install and tighten all required fasteners using the applicable manufacturer procedure.

Do not support loads directly from connection points without approval for the complete truss system.

Verify connection interfaces and completed-system suitability before combining different systems.

Have a competent person perform a documented inspection at least annually and remove unsafe parts from service.

Truss Section Questions

EVT12S-5FT-Black Frequently Asked Questions.

What is a black five-foot truss section used for?

It is a 60 in / 5 ft matte black straight section used to build out a truss run in standard 12-inch end-plate systems. Typical jobs include broadcast and studio systems, touring production, nightclub and venue production, product launches, and seasonal event builds where matte black components are specified.

Can I use it in a run with brushed aluminum sections?

The finish is cosmetic, so a black section and a brushed section can look different side by side. The end-plate interface still has to match. Verify end-plate dimensions, bolt-hole positions, hardware and full seating at every joint before you combine them.

How should I use the Load-Span Reference with a black five-foot section?

The reference describes completed 12 x 12 truss runs at 10, 20, 30 and 40 ft spans, not an individual section. A five-foot section is one part of the full span, so add up every section in the run to find its total length. Have a licensed structural engineer review the complete configuration before use.

How heavy is the black five-foot section, and is it certified?

It weighs 35 lb / 15.88 kg and is built from EN AW-6061-T6 aluminum with 50 mm main tubing and 25 mm diagonal brace tubing, in a matte black powder coat. It is TÜV certified and carries a 1-Year Limited Manufacturing-Defect Warranty. Use a safe lifting method when you place it overhead.

Need an EVT12S Five Foot Black Truss Section?

Contact us for truss section selection, listed compatibility information, product documentation, and quantity-quote support.

Structural Solutions, Unmatched Innovation

Weight	33 lbs
Dimensions	60 × 13 × 13 in